Erico CADDY ROD LOCK Channel Nut User Manual download pdf

Tighten to

45 ft-lbs[61 N-m]

1 TURN

Pull

Load

Slip

Load

1 2

Load Rating

Top Up Mounting

(See note 1)

Nut side is always the top side

*Load must not exceed capacity of channel.

Not for use with hot dip galvanized hardware/components.

A - SAE

J429 GRADE 2; ASTM

A307 GRADE A,B,C; ISO

898 GRADE 4.6

B - SAE

J429 GRADE 5; ASTM

A449; ISO

898 GRADE 8.8

*Arrow on CADDY

ROD LOCK Channel Nut must always point down.

U.S. Part No.

Europe Article

Number

Rod Size

Pull Load Pull Load

Slip Load

CRLS37EG

N/A

3/8"

750 LBS

1200 LBS

400 LBS

CRLSM8EG

390003

2750 N 5000 N 1750 N

CRLSM10EG

390004

M10

3750 N 6000 N 1750 N

CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.

TECHNICAL SUPPORT:

www.erico.com

CFS411_F

INSTRUCTION SHEET

NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.

The customer is responsible for:

a. Conformance to all governing codes.

b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.

c. Using appropriate industry standard hardware as noted above.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

1 OF 2

WARNING:

ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at

www.erico.com

and from your ERICO customer service representative.

ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and death.

Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.

All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any

other purpose.









ASTM is a registered trademark of American Society for Testing and Materials

ISO is a registered trademark of International Organization for Standardization

SAE is a registered trademark of SAE International

1 2

 1

Summary of Contents

Page 1 - 

Tighten to45 ft-lbs[61 N-m]1 TURNPullLoadSlipLoad1 23 Load Rating 5Top Up Mounting (See note 1)Nut side is always the to

Page 2

Tighten to 45 FT- LBS (61 N-m)1257Bottom Up Mounting (See note 1)4Note 1For the up-thrust load or high amplitude vibration application, add a jam nut

Comments to this Manuals

No comments

Erico CADDY ROD LOCK Channel Nut User Manual

Browse online or download User Manual for Accessories for electrical Erico CADDY ROD LOCK Channel Nut. ERICO CADDY ROD LOCK Channel Nut User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for electrical Erico CADDY ROD LOCK Channel Nut